Skip to content

CSLB License #1162060 · Based in Imperial Beach, CA

Flat Roofing

Torch-down roofing for flat and low-slope roofs: rolled sheets with seams sealed by heat.

CSLB License #1162060 · Bonded · Based in Imperial Beach, CA

The service

Flat roofs have to hold water off.

A flat roof is never perfectly flat. It is built with a slight slope so water moves toward drains, scuppers or the edge. Because water moves slowly across it, a flat roof has to work as one continuous waterproof sheet.

Torch-down is a common way to build that sheet. Rolls of modified bitumen are laid in overlapping layers, and the laps are heated with a torch so they melt together and seal.

Worker spraying a light coating on a flat roof

Common jobs

  • Flat roof replacement

    Old flat roofing removed and new torch-down installed.

  • Garages and patio covers

    Low-slope roofs over garages, carports and covered areas.

  • Additions

    Flat sections tied into a sloped main roof.

  • Flat roof repairs

    Blisters, open seams and worn spots fixed in place.

Sealed by heat

One sheet, sealed at every seam.

Torch-down builds a flat roof from overlapping rolls. The laps are where it is won or lost, so every one is heated and sealed.

WATER RUNS TO THE DRAIN123456
  1. 1. Roof deck

    The wood the flat roof is built on, sloped slightly toward drains or edges.

  2. 2. Base layer

    The first layer of roofing over the deck.

  3. 3. Cap sheet

    The top layer, often with a granule surface that faces the sun.

  4. 4. Torched lap

    Where two rolls overlap and are melted together to seal.

  5. 5. Edge metal

    Metal at the roof edge that finishes the sheet and guides water off.

  6. 6. Drain

    Where water leaves the roof. It is flashed into the membrane.

Planning

What shapes the job.

No two roofs are the same. These are the things that change how flat roofing work is planned.

Slope and drainage
Where water goes now, and whether low spots need attention.
What is there now
Old roofing that has to come off before the new layers go down.
Deck condition
Wet or soft wood under a flat roof is common and gets replaced.
Walls and parapets
Where the flat roof turns up a wall, it needs flashing that ties in.
Openings
Vents, skylights, AC stands and pipes all need sealing.
How it ties in
Where a flat section meets a sloped roof on the same house.

Before you call

Nothing here is required. A few of these help us understand the roof.

  • Photos of the flat roof surface and the edges.
  • Where water sits after rain, if you have seen it.
  • Where leaks show up inside.
  • What is up there: AC units, vents, skylights.
  • How you get onto the roof, if there is a way.
  • Gate codes or access notes for the property.

Photos and questions can go straight to (619) 707-6224 by call or text.

What's involved

How the work goes.

Every roof is different. This is the general order of the work, and we go over the specifics for your roof with you.

  1. Step 1: Look at the roof

    We look at the surface, the seams, the edges and where water goes, including any spots where it sits after rain.

  2. Step 2: Prepare the surface

    Old roofing comes off as needed and the deck is checked. Damaged wood is replaced.

  3. Step 3: Base and cap layers

    A base layer goes down, then the cap sheet is torched in place with every lap heat-sealed.

  4. Step 4: Edges and openings

    Edge metal, drains, walls and anything passing through the roof are flashed and sealed.

Flat Roofing questions

What is torch-down roofing?

Rolled sheets of modified bitumen laid on a flat or low-slope roof. A torch heats the underside and the laps so the layers bond and the seams seal together.

Why does water sit on my flat roof?

Low spots, sagging deck or blocked drains can leave standing water, often called ponding. Finding the cause is part of planning the repair or the new roof.

Can a flat roof be coated instead of replaced?

Sometimes. A coating can go over a flat roof that is still sound underneath. If the roof is wet or failing below the surface, it usually needs repair or replacement first. See our roof coatings page.

How do I get an estimate?

Call or text (619) 707-6224, or send a request through the estimate form. Tell us about the roof and what is going on with it.

Estimate

Tell us about your roof.

Tell us what you have in mind. Prefer to talk? Call or text (619) 707-6224.

Request an estimate

Tell us about the project.

Required